Sub Categories
Automated Total Nitrogen/Phosphorus/COD Analyzer NPW-160 Measuring based on official measuring method Multiple-wavelength detector enables measurement of total nitrogen, total phosphorus and COD simultaneously Space-saving design attained by eliminating back piping Drip-proof construction Meas. range Total nitrogen: 0 - 2 mg/L to 50 mg/L Total phosphorus: 0 - 0.5mg/L to 20 mg/L COD (UV method): 0 - 2 Abs
Current Range: 1 to 600 A DC or AC Peak Basic Accuracy (DC to 400 Hz): +/- (2% of reading + 1 A) Output Signal: 100 A range: 10 mV/A | 600 A range: 1 mV/A Frequency Range: 40 Hz to 400 Hz Working Voltage: 600 V AC rms Maximum Conductor Diameter: 34 mm (1.34 inch) Safety Rating: IEC 1010 and CSA-C22.2 No. 1010-1 Installation Category II, Working Voltage 600V
GMS-1000 is one point digital controller which can be connected to only one(1) gas detector. Receiving analogue continuous signal from one (1) detector and converting it into digital signal, GMS-1000 provides various alarming and monitoring environment by micro-processor. Also, GMS-1000 converts digital signal into the 4-20㎃ standard current signal for output signal which can be transmitted to various external devices such as PLC, DDC, RECODER, and so on. Using these functions, you can easily construct the gas monitoring system more extensive as well as more comprehensive.
Features Max. Current 3AFor: GPR-U/H/M Series,GPC/GPS/PPE/PPS/PPT/PSS/PST-Series
World’s First Non-Metallic Contact Voltage Tester Measures 600V With Optimal Safety Hioki leads the industry in non-metallic contact test and measurement technology that promotes safety on the worksite. The 3258 is a line voltage tester that employs a coupling capacitance cancellation method to measure voltage in AC circuits without requiring metal-to-metal contact. Voltage can be measured safely at practically any location, on either insulated or exposed metal conductors.
FEATURES ● Microprocessor-controlled.● Four terminal measurement.● Measures down to 100μΩ.● 5 Ranges from 200.0mΩ to 2000Ω.● Maximum resolution of 100μΩ.● Three test currents with over-temperature protection.● Protection against inadvertent connection to over voltage.● Large LCD.● Potential lead resistance and current lead resistance checks.● "Full-featured” EnerSave inside.● EnerSave Auto hold.● EnerSave Auto off.● Lightweight, robust & compact.● Indicators show if reading may be invalid (RP, RC, and temperature).● "O-Ring” sealed case. SPECIFICATIONS Measuring ranges 0-200.0mΩ in steps of 100μΩ 0-2000mΩ in steps of 1mΩ 0-20.00Ω in steps of 10mΩ 0-200.0Ω in steps of 100mΩ 0-2000Ω in steps of 1Ω Accuracy ±0.5% of reading ±2 digits over the operating temperature range, -15ºC to +55ºC, with the supplied test leads Test current 1mA=>2000Ω range 10mA=>200 / 20Ω ranges 100mA=>2000m / 200mΩ ranges Test current accuracy ±0.1% Protection fuses Mains = 0.5A,...
Industrial pH Transmitter HDM-135A(2-wire)/HDM-136A(4-wire) Easy-to-use pH analyzer for field installation in a compact and rigid aluminum enclosure Easier calibration done with standard solution Auto determination of electrode deterioration Alterable output range Automated self-diagnosis of fault (burn-out output) Meas. range -1 - 14
Features * Wide frequency range from 1uHz to 80/50MHz* High 200MSa/s sampling rate * 16-bit Amplitude Resolution* Output from any section of 1M-point-long waveforms* 4.3" high resolution LCD display/on-screen help/Impedance switch* Four ways to generate arbitrary waveforms: Front Panel Operation CSV file uploading, Direct Waveform Reconstruction (DWR), ArbitraryWaveform Editing PC Software * USB, RS-232, GPIB interface support